CNC Spindle Motor & Tool Parts. ER20 Spindle Motor 4.5KW Water Cooled 380V 24000rpm&5.5KW VFD Inverter Kit. ER20 Spindle Motor 4.5KW Water Cooled 380V 24000rpm&5.5KW VFD Inverter Kit CNC Engraving Cutting. High-Speed Constant Torque Motorized Spindle Motor for CNC engraving machines. Bearing(half year), spindle(one year).
Folder knife diameter : 3.175, 4, 6, 12.7 mm Cooling : water-cooled Material : 304 stainless steel Voltage and current : AC220v common household electric, must through the inverter output Radial runout : 0.01mm Coaxial degree : 0.025mm Dimensions : 100 260mm Nut model : ER20-M type or A-type optional Speed mode : through the inverter to adjust the output voltage and frequency can be achieved 0-24000 stepless Cooling: water cooling mode Power Interface : use GX16 waterproof aviation interfaces, there are 1234 mark, 123 are connected to the drive power supply (U, V, W), 4 are connected with inverter earth Lubrication : high temperature grease. 4.5KW VFD Driver Inverter Specifications. 3-phase AC 380V ±20% 50/60Hz. Electric spindle is a high-speed high-precision components rigidity, we must strictly follow the practices used spindle spindle motor, otherwise it will increase equipment failures, shorten equipment life. Please use the rule as follows.
(1) Before the boot, first ensure that the spindle cooling system to work properly, and then turn the power spindle. Do not use the spindle without the cooling conditions, it is necessary to check the fan and pump are working properly before use. If the spindle is water cooled, to check whether the cooling water containing impurities to ensure water is smooth. (2) When using electric spindle, spindle from low according to the principle of high speed, gradually increasing speed to warm up, when the spindle load up to speed and smooth operation of the state after the required processing, can better protection spindle, to reduce the wear.
(3) during use is strictly prohibited beat, hit threaded spindle clamp and rotor end, so as not to reduce the component life, affect the results spindles used. (4) During the operation, the tool must be replaced in the correct way. When the knife, the focus should be uniform, the tool should be aligned with the threaded end of the screw rotor, clamping can be. During operation the tool needs to be replaced before the replacement to wait Spindle cooling, avoid tool change at hot temperature state.(5) During the operation, if the fixture card spindle rotor end, non-beat way to remove Jigs. Only under the premise of no damage to the rotor shaft threads with pliers and other tools to remove the chuck, and clean the rotor tapered bore and clamp the spindle to avoid Movies shorten life, affecting the quality of workpiece. If the fixture has completely lost precision, it must be replaced immediately.
(1) to control the spindle actual time worked. Theoretically prohibit spindle 24 hours of continuous work, operating 12 hours per spindle Spindle let rest at least 2 hours, in order to prevent the formation of shortened due to mechanical fatigue life of the spindle. (2) to understand the conditions, the ambient temperature and the spindle temperature control.Spindle operating ambient temperature not higher than 35 centigrade degree, when the ambient temperature is above 35 centigrade degree should use air conditioners or other protective measures to reduce the room temperature, thereby reducing spindle temperature. (3) The spindle cooling water must be kept clean and free of impurities, recommendations to clean up after the end of the spindle shaft waterway, scale and water holes to avoid clogging due to rust. Also, always pay attention to circulating water temperature in the tank, so the water temperature is too high, the cooling effect can not be achieved prefetching.
(4) Always check the power supply connector, to avoid damage to the connector loose or aging brings to the spindle and the drive. (5) If the downtime to use again, you must tranches from low speed to high speed spindle run-in steps according to the spindle load running, in order to use in the run-through.
(6) during the loading and unloading cutter knife, must tool chuck nut clean. (1) must match the drive spindle chosen correctly according to the electric spindle nameplate good debugging power, voltage and frequency. (2) Set the frequency converter should be set command channel, and then set the display channel, and finally set the parameters. When setting parameters, be sure that the reference frequency, the frequency of the three highest rated frequency and consistency. (3) The spindle is generally clockwise in the wrong direction, the drive can change settings or swap any two rotating wire the inverter output UVW terminal on.
(4) In general, water-cooled spindle surface temperature and ambient temperature greater than 20 degrees, the heat can be considered a spindle; when air-cooled spindle surface temperature greater than ambient temperature of 30 degrees, can be identified as the main heat seriously, immediately shut down cooling, a check. 1 Spindle found abnormal sound, should immediately stop checking.
(2) the operation of an abnormal burning smell, immediately stop checking. (3) If the spindle does not run the boot, do not start over, you should carefully check the following related matters: first check the drive parameters to determine the input and output voltage, the spindle parameter settings are correct. Second, check the power cord and wiring connector is plugged in and determine whether the contact connector problem. (4) Since the electric spindle is a high speed, high rigidity precision components and must therefore be sent back to me by professionals or for repair.Feedback is very important to us. So that we can address your concerns. It is impossible to address issues if we do not know about them! Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. If you need any CNC parts or repairs, welcome to contact me, we will try our best to help you. If it's non-workdays, please kindly be patient and wait till Monday. The item "ER20 Spindle Motor 4.5KW Water Cooled 380V 24000rpm&5.5KW VFD Inverter Kit" is in sale since Thursday, August 10, 2017. This item is in the category "Business & Industrial\Automation, Motors & Drives\Electric Motors\General Purpose Motors". The seller is "vipwindows_168" and is located in shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.