Water Cooling Kit

Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled

Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled
Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled
Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled
Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled
Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled
Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled
Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled

Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled
Miller Diversion 165, 180 & Hobart EZ-TIG 165i Air & Water-Cooled TIG Torch Upgrade Kit. Upgrade the Power and Work Lead connections on your Miller Diversion machine and benefit from improved performance and greatly expand your welding capabilities. Enjoy the benefits of a high-performance Air or Water-Cooled TIG torch! Miller Diversion machines come from the factory with a contractor style 12.5' (3.8m) Torch and Work Lead that is "hard-wired" to the Machine. What's more the OEM torch is bulky and cumbersome which greatly reduces the machines versatility, performance, and your ability to comfortably manipulate the torch which is critical to high-quality TIG welding.

The JW Signature Series Upgrade Kit makes it easy for you to install Dinse style TIG Power and Work Lead connections. The conversion is simple, and can be done in a few minutes with our complete upgrade kit and standard shop tools.

Female Dinse Panel Mount (black) TIG Torch Receptacle. Female Dinse Panel Mount (red) Work Lead Receptacle.

Male Dinse (red) Work Lead Connector. Delron Hole Saw Guide Bushings. All related mounting hardware and accessories. Turn Off Machine's Power Switch and UNPLUG THE POWER CORD!

Remove the machine cover, factory-installed TIG Torch and work lead connector and strain relief(s). Save the covered Work Lead cable with Eyelet Connector. Cut the covered Work Lead (opposite the Eyelet Connector) so you have 12 of work lead cable.

This will be your new Internal Work Lead connection to the (red) Panel Connector. Strip the end of the covered Work Lead (opposite end of the Eyelet Connector) and connect the Arc-Zone supplied 45 degree angle connector. Using the Arc-Zone supplied hole saw drilling kit, enlarge the two existing holes in the machine's front panel to 30mm. File a 1/4" x 1/4" (6.4mm) "keyway" relief into the enlarged the 30mm holes (it's best to locate each relief at the "6 o-clock" position) on the chassis of your machine. This allows the New Female Panel Receptacles to nest properly and keeps them from rotating.

If you do not perform steps 5 & 6, you could have the Welding current in direct contact with the machines chassis. Disassemble the Black and Red panel Mount Receptacles and insure that they fit into the holes on the machines front panel.

Note: There is an insulator for the inside and outside of the machine chassis, and both have a 1/4 (6.4mm) notch that must be lined up during assembly. Install TIG torch panel mount connector, (Black) into Upper Hole in machine face, with flat and lock washer so as to sandwich the machines power eyelet. Install Work Lead panel mount connector, (Red) into Lower Hole in machine face. Tighten the Work Lead eyelet connectors to the mother board and the Lower (Red) Panel Connector. Verify that all connections are tight and Re-install the machine cover.

Complete your upgrade with a new high-performance TIG torch! Select the torch and amperage that best fits your application.

Enjoy your upgraded Diversion, and good welding! Complete Your Upgrade with a New TIG Torch. CK-130 - 2 Series, 130 amp Air-cooled.

CK-150 - 3 Series, 150 amp Air-cooled. CK-200 - 2 Series, 250 amp Water-cooled.

CK-130 FX - 2 Series, 130 amp Air-cooled. CK-150 FX - 3 Series, 150 amp Air-cooled. CK Flex-Loc Articulating Head Torch Models.

CK-FL130 - 2 Series & CK-FL150 - 3 Series, Flex-Loc Air-Cooled. CK-FL230 - 2 Series & CK-FL250 - 3 Series, Flex-Loc Water-cooled. Upgrade your Foot Pedal too!

2091 Las Palmas Drive, Ste. The item "Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled" is in sale since Monday, July 1, 2019. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\MIG, TIG & Stick Welding Accessories\Other MIG, TIG & Stick Accessories". The seller is "arc-zoneweldingsupplies" and is located in Carlsbad, California.

This item can be shipped worldwide.
  • MPN: JWS-MDCK-D
  • Country/Region of Manufacture: United States
  • Brand: Miller
  • Item Type: TIG Torch Upgrade Kit

Miller Diversion TIG Torch Upgrade Kit Air/Water-Cooled